Ethernet Lab free essay sample

Purpose The purpose of this experiment is to study the workings of Ethernet cables to enhance practical knowledge of application. II. Apparatus 1) Standard Cat5 Ethernet Cable (6feet long 2) RJ45 Connectors 3) Multi Network Cable Tester 4) RJ45 Wire Crimp Tool amp; Cable Stripper III. Procedure 1) Determine the type of Ethernet cable that needs to be created, either â€Å"Straight through† or â€Å"Cross Over†. For this experiment, a Straight through cable will be required. 2) Cut an Ethernet cable of 6feet in length from the bulk cable in the box. ) Use the RJ45 Wire Crimp Tool amp; Cable Stripper, using the bottom of the tool for Cable striping, strip off at least 1inch of the plastic casing to expose the inner wires. 4) Separate the Wires into their colored pairs for easier distinction. (ex. Orange and Orange White, etc) 5) Now that the cable colors are easier distinguish, the pattern required for a Straight through cable from left(1) to right(8) are as follows 1. We will write a custom essay sample on Ethernet Lab or any similar topic specifically for you Do Not WasteYour Time HIRE WRITER Only 13.90 / page Orange-White 2. Orange 3. Green-White 4. Blue 5. Blue-White 6. Green 7. Brown-White 8. Brown 6) Repeat Steps 3,4 and 5 on the opposite end of the Ethernet cable. ) Once the pattern above is reached, insert the exposed wires into the RJ45 and determine if they are fit to be crimped. Remember, no inner wires should be outside of the RJ45 connector. Trim the inner wires so that they go into the pin and the Ethernet shielding goes into the section of the connector that requires crimping. 8) Place the cable with connector into the RJ45 9) 10) Once you have determined the network cable you will be creating strip the cable, we recommend stripping at least a half of an inch off of the cable to expose the inner wires. Dont be worried about stripping too much of the network cable jacket off since you can always cut the wires down more if needed later. After the network cable jacket has been removed separate the wires within the cable so they can be put into the RJ-45 connector. IV. Results The Ethernet Cable was tested using a Multi Network Cable Tester by plugging both ends of the cable into the device. The Multi Network Cable Tests, tests for continuity and sequencing in each connections indicated by two 9-way LEDs. The Ethernet Cable constructed in this experiment performed flawlessly one testing Device. Additionally, after the Ethernet cable was plugged in, the Multi Network Cable Tester began indicating Continuity on pin 4 of both ends of the Ethernet cable. Then, it continued onto pin 5,6,7 and 8 which gave a positive indication for Continuity amongst its paired pins. Lastly, the Tester jumped back to pins 1. 2 and 3 which also gave a positive reading for continuity and when PIN Number(Cable End 1)| PIN Number(Cable End 2)| Connectivity| 4| 4| Passed| 5| 5| Passed| 6| 6| Passed| 7| 7| Passed| 8| 8| Passed | 1| 1| Passed| 2| 2| Passed| 3| 3| Passed| V. Conclusion The Ethernet Cable is a piece of computer equipment that is utilized to connect computers to networks to make data transmission possible. During this experiment, the Ethernet Cable was constructed and tested to determine whether Ethernet cable was adequate to perform the task of data transmission. According to the collected data, the Ethernet Cable (straight through) created, was able to sequence with its pair and passed continuity, which made this experiment a success. Some of the factors that complicated the process of this experiment were mainly the Ethernet Cable itself. During the separation of color coded inner wires, mention in procedure step 5, the wires kept on breaking very easily which caused those wires to be cut and start the experiment over again. This occurrence was mainly due to human error, when the Ethernet cable was put through the Stripping process of the RJ45 Wire Crimp Tool amp; Cable Stripper, the tool was process too hard that after making and incision on the yellow plastic shielding of the Ethernet cable, it also made a slight cut on the inner wires themselves. Thus, when the cable were bent on the separation phase, they simply snapped off.